THREE PART SPECIFICATION

{edit to suit project requirements}

PART 1 –GENERAL

1.01 Summary

This section includes toilet compartments and screens as follows:

1. Type and series:

2. Style and configuration:

3. Urinal and privacy screen:

1.02 Submittals

Product Data:

Submit manufacturer’s current technical data for materials, fabrication,

finishing, fastenings, hardware and installation details.

Shop Drawings:

Submit shop drawings of field measurements for fabrication, installation

and assembly of project. Show complete layout and elevations of partitions.

Indicate door swings, method of mounting, bolt hole locations,

details of adequate steel reinforcement or wood blocking in walls.

Samples:

Submit samples of manufacturer’s standard colors and hardware for

selection and approval by architect.

1.03 Field Measurements and Project Conditions:

Verify final dimensions of field measurements as indicated on shop

drawings before fabrication and installation.

1.04 Delivery, Storage and Handling:

Deliver and store material in original crates with protective plastic

covering. Protect from all possible damage while stored at site.

PART 2-PRODUCTS

2.01 Acceptable Manufacturers:

Laminating Technologies, a division of YTI Enterprises, Inc.

2.02 Materials: (see detailed individual product specification)

- PLASTIC LAMINATE

- SOLID PHENOLIC

- POLYMER

PART 3-EXECUTION

3.01 Installation:

a. Install partitions secure, rigid, straight, level and plumb.

b. Install pilasters in position with manufacturer’s recommended mounting

devices.

c. Allow for spacing between wall and pilasters (1”), and between panels

and walls (1/2”).

d. Equip each door with hinge, slide latch, strike, keeper, coat hook and

door bumper. Outswing door are to be provided with door pull.

e. For floor mounted overhead braced pilasters secure heavy-duty, antigrip

aluminum headrail.

3.02 Adjustment:

a. Adjust and align door hinges for correct positioning and operation of

door.

b. Adjust all partition components for consistent horizontal level lines.

c. All surfaces shall be cleaned after installation is complete.

d. Job site shall be left clean and proper after installation is complete.

3.03 Warranty:

Provide manufacturers standard warranty against material, workmanship

and de-lamination.

PLASTIC LAMINATE –Specification

GENERAL MATERIAL INFORMATION

Consists of high pressure impact resistant laminate .048” (1.2mm) that

is decorated all sides to particle board core (45lb. density).

STYLES AND CONFIGURATIONS

1. Floor Mounted

2 .Floor Mounted Overhead Braced

3. Ceiling Hung-adequate backing required

4. Floor to Ceiling Mounted

DOORS AND PANELS

Doors and panels shall be 1” thick.

PILASTERS

Pilasters shall be 1 1/4” thick.

1. Floor Mounted pilasters shall be mounted to the floor with 1/2” x 4”

expansion lock bolt sleeve anchors that are fastened to the bottom of the

pilaster by means of a 3/8” thick x 1” wide steel base bar that is secured

with 3/8” wood hanger bolts inserted 3” deep into the pilaster.

2. Floor Mounted Overhead Braced shall be mounted to floor with adjustable

inter-locking cast metal “L” brackets that are fastened to the bottom of the

pilaster by means of opposite and complementary adjustable inter-locking

cast metal “L” brackets. A leveling bolt inserted in the center of the

pilaster shall be supplied.

3. Ceiling Hung pilasters shall be mounted to the ceiling with 3/8” all

thread rods that are fastened to the top of the pilaster by means of a

3/8” thick x 1” wide steel base bar that is secured with 3/8” all thread rods

inserted 3” deep into a 1” diameter PVC plug embedded within the face

of the pilaster.

4. Floor to Ceiling pilasters shall be mounted to the floor as Floor Mounted

pilasters and shall be mounted to the ceiling as Floor Mounted Overhead

Braced pilasters.

HARDWARE AND FITTINGS

1. Door hardware shall be either:

*Std [A] Wrap around integral chrome hinge with fully adjustable, gravity

type and self-closing action. Hinges are adjustable to pre-set opening or

self-closing angle. Two hinges are supplied per door. Door shall be

equipped with pre-formed and recessed integral hinge that wraps around

pilaster with chrome-plated steel, one-way, theft-resistant fasteners that

are through bolted. Hinge is a heavy-duty chrome-plated finish on durable

zamac casting.

*Optional [B] Wrap around integral stainless steel hinge as per [A] above

but hinge is a heavy-duty cast stainless steel.

*Optional [C] Concealed hardware shall consist of surface mounted hinges

with fully adjustable, gravity type and self-closing action. Two hinges are

supplied per door. Doors shall be equipped with hinge surface mounted

onto door and pilaster with stainless steel, one-way, theft-resistant machine

screws that are tightened into factory installed “T” nut inserts. No screws

are visible on the outside of the compartment except for outswing doors,

door pulls and door bumpers. Hinge is a type 304 satin stainless steel.

2. Slide latch, strike and keeper shall be of heavy-duty chrome plated finish

on durable zamac casting or type 304 satin stainless steel. Coat hook, door

bumper and door pulls of either heavy-duty chrome plated finish on

durable zamac casting or type 304 satin stainless steel are supplied and

installed surface mounted with chrome-plated steel or stainless steel, oneway,

theft-resistant, sheet metal screws.

3. All brackets for panel to wall and panel to pilaster connections shall be

either :

*Std [A] 2 1/2” long, double sided, heavy-duty chrome plated finish on

durable zamac casting stirrup brackets. Brackets shall have rounded

corners.

*Optional [B] 2 1/2” long, double sided, heavy-duty satin stainless steel

stirrup brackets. Brackets shall have rounded corners.

*Optional [C] Concealed by providing three satin stainless steel angle

braced stirrup brackets per connection that are not visible from the outside

the compartment.

4. All wall connections shall be installed with #14 x 1 3/4” chrome-plated

steel or stainless steel sheet metal screw. All panel and pilaster connections

shall be installed with chrome-plated steel or stainless steel, oneway,

theft-resistant fasteners.

5. Pilaster shall have a 4” high sleeve of type 304 satin stainless steel which

conceals all floor and ceiling mounted hardware.

6. For Floor Mounted Overhead Braced, pilasters at the top are secured by a

heavy-duty, anti-grip aluminum headrail.

FINISH

Decorative laminate finish bonded all sides to particle board core. Edges

shall be machined smoothed throughout.

COLORS

Colors shall be selected from current standard line offered.