THREE PART SPECIFICATION

{edit to suit project requirements}

PART 1 –GENERAL

1.01 Summary

This section includes toilet compartments and screens as follows:

1. Type and series:

2. Style and configuration:

3. Urinal and privacy screen:

1.02 Submittals

Product Data:

Submit manufacturer’s current technical data for materials, fabrication,

finishing, fastenings, hardware and installation details.

Shop Drawings:

Submit shop drawings of field measurements for fabrication, installation

and assembly of project. Show complete layout and elevations of partitions.

Indicate door swings, method of mounting, bolt hole locations,

details of adequate steel reinforcement or wood blocking in walls.

Samples:

Submit samples of manufacturer’s standard colors and hardware for

selection and approval by architect.

1.03 Field Measurements and Project Conditions:

Verify final dimensions of field measurements as indicated on shop

drawings before fabrication and installation.

1.04 Delivery, Storage and Handling:

Deliver and store material in original crates with protective plastic

covering. Protect from all possible damage while stored at site.

PART 2-PRODUCTS

2.01 Acceptable Manufacturers:

Laminating Technologies, a division of YTI Enterprises, Inc.

2.02 Materials: (see detailed individual product specification)

- PLASTIC LAMINATE

- SOLID PHENOLIC

- POLYMER

PART 3-EXECUTION

3.01 Installation:

a. Install partitions secure, rigid, straight, level and plumb.

b. Install pilasters in position with manufacturer’s recommended mounting

devices.

c. Allow for spacing between wall and pilasters (1”), and between panels

and walls (1/2”).

d. Equip each door with hinge, slide latch, strike, keeper, coat hook and

door bumper. Outswing door are to be provided with door pull.

e. For floor mounted overhead braced pilasters secure heavy-duty, antigrip

aluminum headrail.

3.02 Adjustment:

a. Adjust and align door hinges for correct positioning and operation of

door.

b. Adjust all partition components for consistent horizontal level lines.

c. All surfaces shall be cleaned after installation is complete.

d. Job site shall be left clean and proper after installation is complete.

3.03 Warranty:

Provide manufacturers standard warranty against material, workmanship

and de-lamination.

POLYMER –Specification

GENERAL MATERIAL INFORMATION

High-density polyethylene with textured surface composed from extruded

polymer resin with uniform color throughout.

STYLES AND CONFIGURATIONS

1. Floor Mounted

2. Floor Mounted Overhead Braced

3. Ceiling Hung-adequate backing required

4. Floor to Ceiling Mounted

DOORS AND PANELS

Doors and panels shall be 1” thick and 55” high overall.

*Optional - Doors and panels shall have an extruded aluminum heat

resistant strip attached to the lower edge

PILASTERS

Pilasters shall be 1” thick

1. Floor Mounted pilasters shall be mounted to the floor with 1/2” x 4”

expansion lock bolt sleeve anchors that are fastened to the bottom of the

pilaster by means of a 3/8” thick x 1” wide steel base bar that is secured

with 3/8” all thread rods inserted 3” deep into a 1” diameter PVC plug

embedded within the face of the pilaster.

2. Floor Mounted Overhead Braced shall be mounted to floor as Floor

Mounted pilasters.

3. Ceiling Hung pilasters shall be mounted to the ceiling with 3/8” all

thread rods that are fastened to the top of the pilaster by means

of a 3/8” thick x 1” wide steel base bar that is secured with 3/8” all

thread rods inserted 3” deep into a 1” diameter PVC plug embedded

within the face of the pilaster.

4. Floor to Ceiling pilasters shall be mounted to the floor as Floor Mounted

pilasters and shall be mounted to the ceiling as Ceiling Hung pilasters.

HARDWARE AND FITTINGS

1. Door hardware shall be either:

*Std [A] Wrap around aluminum hinge 8” high with fully adjustable,

gravity type and self-closing action. Hinges are adjustable to pre-set

opening or self-closing angle. Two hinges are supplied per door. Door

shall be equipped with hinge surface mounted onto door and pilaster

with stainless steel, one way, theft-resistant fasteners that are through

bolted. Hinge is a heavy-duty extruded aluminum with a bright anodized

finish.

*Std [B] Integral hinge with fully adjustable, gravity type and self-closing

action. Door and pilaster shall be machined to accept integral hinge

mechanism with no exposed hardware. Door and pilaster shall be

equipped with two hinge pins. The bottom pin shall have a 1/2” diameter

nylon with a 3/16” stainless steel center pin for gravity type action. The

top pin shall have a 1/2” diameter nylon. Hinge assembly is pre-formed

and factory pre-drilled.

*Optional [C] No sight integral hinge with fully adjustable, gravity type

and self-closing action. Door and pilaster shall be machined with an

overlapping edge to accept integral hinge mechanism with no exposed

hardware. Opposite pilaster with strike shall be machined to accept

overlapping edge of door. Door and pilaster shall be equipped with two

hinge pins as per [B] above.

*Optional [D] Cosmo Set: full height, spring loaded, gravity type and

self-closing action piano hinge at 54” overall length. Door shall be

equipped with hinge surface mounted onto door and pilaster with

stainless steel, one-way, theft-resistant fasteners that are through bolted.

Hinge is a heavy-duty extruded aluminum with a bright or satin anodized

finish.

2. Slide latch, strike and keeper shall be of heavy-duty extruded aluminum

with bright anodized finish or type 304 satin stainless steel. Coat hook,

door bumper and door pulls are either heavy-duty extruded aluminum

with a bright anodized finish or type 304 satin stainless steel are supplied

and installed surface mounted with stainless steel, one-way, theft-resistant

sheet metal screws.

3. All brackets for panel to wall and panel to pilaster connections shall be

either :

*Std [A] 3” double height stirrup bracket of heavy-duty extruded

aluminum with a bright anodized finish.

*Optional [B] Cosmo Set: full length 54” heavy-duty extruded aluminum

double sided “F”, ”T” and ”U” brackets which shall be pre-drilled. One

bracket shall be provided for each connection.

*Optional [C] Spectrum Set: full length 54” heavy-duty, type 304 satin

stainless steel double sided “F”, ”T” and ”U” brackets which shall be

pre-drilled. One bracket shall be provided for each connection.

4. All wall connections shall be installed with #14 x 1 3/4” stainless steel

sheet metal screw. All panel and pilaster connections shall be installed

with stainless steel, one-way, theft-resistant fasteners.

5. Pilaster shall have a 4” high sleeve of type 304 satin stainless steel which

conceals all floor and ceiling mounted hardware.

6. For Floor Mounted Overhead Braced, pilasters at the top are secured by a

heavy-duty, anti-grip aluminum headrail.

FINISH

Uniformed polymer color throughout with radius edges.

COLORS

Colors shall be selected from current standard line offered.